Products
Spa-Pool Septic Systems
Item no.: N/AOur Spa-Pool Septic System is designed to efficiently separate and drain chlorinated wastewater. Manufactured from fiber-reinforced composite material, the system provides high strength, long operational lifespan, low weight, and easy installation.
The system is delivered with a Ø110 mm gravitation discharge pipe, complete with all relevant fittings. For sites with heavy loads or challenging soil conditions, the Spa-Pool Septic System can be further reinforced to withstand pressure from groundwater, soil, and other external forces.
- Construction: Made from fiber-reinforced composite material for exceptional strength and a long service life.
- Lightweight design: Easy to handle, transport, and install.
- Corrosion-resistant: Maintains performance and integrity in harsh environments.
- Reliable durability: Built to withstand demanding applications over time.
Sizes and Specifications
| Diameter | Volume | Height | Discharge zone |
|---|---|---|---|
| 1250 mm | 1 m³ | 1400 mm | 1 x 15 m |
Options
- Can be further reinforced to withstand pressure from groundwater.
- Can be further reinforced to withstand heavy traffic loads.
- Can be further reinforced to withstand soil pressure.
Extra equipment
Item no.: N/A FRP Shafts without Sleeves
Learn More
×
FRP Shafts without Sleeves
FRP shafts without sleeves are commonly employed for extending wells. These shafts are manufactured using composite material - fiberglass, a corrosion and chemical-resistant material.
| Diameter | Height |
|---|---|
| 315 mm | 500 mm |
| 315 mm | 1000 mm |
| 315 mm | 1500 mm |
| 315 mm | 2000 mm |
| 425 mm | 500 mm |
| 425 mm | 1000 mm |
| 425 mm | 1500 mm |
| 425 mm | 2000 mm |
| 580 mm | 500 mm |
| 580 mm | 1000 mm |
| 580 mm | 1500 mm |
| 580 mm | 2000 mm |
| 780 mm | 500 mm |
| 780 mm | 1000 mm |
| 780 mm | 1500 mm |
| 780 mm | 2000 mm |
| 900 mm | 500 mm |
| 900 mm | 1000 mm |
| 900 mm | 1500 mm |
| 900 mm | 2000 mm |
Item no.: N/A High water level alarms
Learn More
×
High water level alarms
High Water Level Alarms can be installed in e.g., rainwater tanks, collection tanks, pumping wells, precipitation tanks, etc.
The alarm will signal at the pre-set height.
The level float is on top of the water and when it reaches the level switch, the alarm will signal.
Comes with:
- High water level alarm SPHA-2
- Level float
- Level switch
- Mounting equipment
- 4 screws
- Zip-ties for mounting of level float
Installation
Lower the level float down until reaching the wanted alarm level. Mount on the inside of the access shaft. The level float can be mounted on the service step for easy hoisting/lowering in case of service or adjustments.
| Types | Width | Height | Depth |
| SP-HA2 | 145 mm | 170 mm | 120 mm |
Technical Diagram
Electrical Diagram
Item no.: N/A Septic tank alarms – Lokaset 20
Learn More
×
Septic tank alarms – Lokaset 20
Lokaset 20 septic tank alarm is a full alarm system for supervision of overflows in precipitation and collection tanks.
Lokaset 20 is a conductively controlled safety device consisting of a sensor unit and a control box. When the sensor comes in contact with a conductive fluid, the control box will put out a signal: turning on the red indicator lamp, buzzing starts, and disconnecting the alarm relay. By pressing the alarm receipt button, the buzzing will be turned off. The indicator lamp will continue to light up, and the relay will still be disconnected until the alarm is removed i.e., the sensor is no longer in contact with the fluid. The alarm is equipped with a 4-5 seconds delay to avoid unnecessary alarm because of splashes.
SET/LV sensor: The sensor and belonging cable are equipped with a fault-finding device that can localise breakdowns in the sensor circuit. The device is powered by 230VAC mains through a connecting cable with a standard plug. When the device is in on-mode, the alarm relay is in alarm setting i.e., disconnected. When the device is powered, a green light will turn on.
NOTE! The alarm must not be used for installations in areas with risk of environmental damages. SET/LV or SET/L sensor must not be installed in areas with risk of environmental damages.
It is not recommended to install SET/LV or SET/L sensor in areas where fumes, gasses, or fluids with possible corroding effects on the sensor are present e.g., aromatic and chlorinated hydrocarbons (PVC), strong bases or acids.
Comes with:
- Control box with indicator
- Indicator light and buzzing alarm
- SET/LV overflow sensor
Benefits:
- Easy to install
- Visual and acoustic signal alarm
- Avoid overflow of tank
- ATEX-certified
| Types | Certification | W x H x D | Supply voltage | Ambient temperature | Compatible sensors |
| SP Lokaset 20 | ATEX | 130 x 80 x 35 mm | 230 V ±10%, 50/60 Hz, 2,8 VA | 0° C…+50° C | SET/LV, SET/L |